What Size Generator Is Needed to Use the Advent Air RV Air Conditioner

Question

Question:

Will a 2,000 watt generator power this ac unit?

asked by: Jim

0

Expert Reply:

The Advent Air RV Air Conditioner with Ceiling Vent and Start Capacitor part # ACM135BC requires 3,000 watts for starting and 1,000 watts while running therefore a 2,000 watt generator would not be suited for this or any RV air conditioner for that matter. Instead, I recommend the A-iPower 3,800-Watt Portable Inverter Generators - 3,000 Running Watts - Gas - Manual Start # 289-SUA2000i-2 which has a 3,800 watt starting and 3,000 watt running power output. This will give you enough power to start and run the air conditioner as well as power a few other items if you need to.

The main issue you run into when using an air conditioner with a portable generator is the high starting wattage required for the air conditioner. However, the start capacitor included with the above air conditioner brings the starting watts way down to allow for a more cost effective generator to be used. For example, if you were using the Advent Air RV Air Conditioner with Ceiling Vent without the start capacitor then it would require almost 6,000 watts for starting.

I have attached a review video on the generator for you as well.

expert reply by: Conner L

0

Answer 1

The Advent Air RV Air Conditioners #ACM135 that you referenced draws 1,450 watts. A 2,000 watt Honda generator would easily work to power this. We have a 2,000 watt generator from A-iPower part #289-SUA2000i that would also work and cost less than a…

view full answer...

Answer 2

Thanks for reaching out, for you I recommend going with the parts below. **Advent Air RV Air Conditioner w/ Air Distribution Box and Start Capacitor - 13,500 Btu - Black #ACM135BC. **Advent Air RV Air Conditioner w/ Air Distribution Box and Start…

view full answer...

Answer 3

So there's a few things that are going to be needed in order to install the Advent air conditioners, and for a tent trailer I do recommend going with the smaller 13,500 Btu. But the first thing you need to do is ensure you have a roof that is…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 10

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...