What Does Curt Trailer Hitch part # C12184 Weigh

Question

Question:

How much does this hitch weigh?

asked by: Jeff F

0

Expert Reply:

The Curt trailer hitch part # C12184 that you referenced weighs 29 lbs.

expert reply by: Jameson C

0

Answer 1

When the Thule T2 Classic TH9045 is folded up there will be 3-1/2 inches from the center of its hitch pin hole to the nearest rail. The Curt hitch part #C12184 that you referenced would allow the rack to still fold up as it's not really recessed…

view full answer...

Answer 2

We do have trailer hitch for your 2018 Subaru Crosstek that has a 1 1/4" receiver. With the 1 1/4" receiver you can carry your bike rack without the use of an adapter. The hitch is the Curt Trailer Hitch Receiver - Custom Fit - Class II -…

view full answer...

Answer 3

If you're wanting a 2 inch hitch for your Crosstrek so you can use your existing bike rack, we have 2 options that I would recommend for you. If you don't mind The crossbar of the hitch being visible, the Draw-Tite Class III hitch, part…

view full answer...

Answer 4

Good news, we do have a few options for your 2022 Subaru CrossTrek. The first one is the etrailer Trailer Hitch Receiver #e98912 which is a class III hitch capable of towing a maximum of 3,500 pounds, and a maximum tongue weight of 350 pounds. The…

view full answer...

Answer 5

There are 2 hitches available from Curt that are confirmed to fit your 2020 Subaru Crosstrek. A Class II hitch #C12184, it has a 1 1/4" receiver tube opening and is rated 350 lbs TW, and 3500 lbs GTW. A class III hitch #C13382, it has a 2"…

view full answer...

Answer 6

Class I trailer hitch receivers like #24847 have a distance of about 1-5/8 inches from the center of the hitch pin hole to the welded stop in the back of the hitch receiver tube. Class I ball mounts like #3594 normally are about 1-9/16 inches from…

view full answer...

Answer 7

We have a 1-1/4 inch hitch that fits the hybrid models of the 2020 Subaru Crosstrek like with the Draw Tite part #36644 or the totally hidden EcoHitch part #306-X7365 but the Curt you mentioned does not fit your vehicle.

view full answer...

Answer 8

For a 1-1/4 inch trailer hitch receiver the hitch pin size needed is 1/2 inch diameter. Whether it is a Class I or Class II trailer hitch like the Draw-Tite #36524 you mentioned, you will use the same size pin and clip like #F-4. If you would like a…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Does Curt Trailer Hitch part # C12184 Weigh

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching