What Does Blue Light on Furrion Camera Indicate

Question

Question:

We have a Grand Design Solitude 310GK and a Ford F350 Lariat Dually. The camera and monitor work together just fine, but the blue light on the camera never ever goes off. Whats up? Thank you

asked by: Janeen S

1

Helpful Expert Reply:

If the blue light is active on the camera that would indicate that it's receiving power and is "on". Most likely the camera is wired to the trailer's 12 volt battery as a power source instead of to the running lights or reverse light circuit like some do. Does the monitor display what the camera sees at all times then when it is powered on as well?

expert reply by: Jameson C

1

Answer 1

The Furrion Vision S Wireless RV Backup Camera Systems; part #FOS43TASF for 4.3" screen or part #FOS05TASF for 5" screen, are going to be powered by either the running or backup light circuit. If you don't have the running or backup…

view full answer...

Answer 2

When the system is powered on and the blue light on the monitor appears, do the grid lines still show? If so then the problem is on the camera and you will need to make sure both the power and ground wires are properly secured. If the grid lines do…

view full answer...

Answer 3

On the Lippert Ground Control 3.0 #LC358590 the error you are receiving indicates either a problem at the left front jack, a hall signal issue (open ground/short, or other malfunction) or an unexpected high amperage current stall (meaning the battery…

view full answer...

Answer 4

Because the Furrion monitor goes black it appears the camera either loses power or the monitor does when you shift into reverse. I recommend testing the wires using a circuit tester like #PTW2993 to check for power when shifted in reverse. The…

view full answer...

Answer 5

The most likely cause of the "no signal" error you are receiving with the Furrion Vision S Wireless RV Backup Camera System part #FOS43TASF is due to an interruption on the camera's power wire. Therefore, this will need to be the first…

view full answer...

Answer 6

The Furrion Chill HE Rooftop RV Air Conditioner Setup part #FR23PV contain several parts which all have a two-year warranty. The two-year warranty period is the highest we offer for a rooftop air conditioner. The thermostat has a 1-year warranty.

view full answer...

Answer 7

You've actually done everything you really can do to try and troubleshoot the blurry image from your rear camera so you are in the replacement phase now. Most likely the seals on it failed and allowed moisture to build up inside the lens causing…

view full answer...

Answer 8

A couple of things to check when trying to pair monitor to the camera for the Furrion Vision S #FOS43TASF. First make sure that the monitor is close enough to the camera. Next make sure that the camera is receiving power (indicated by LED light on…

view full answer...

Answer 9

The most likely cause of the "no signal" error you are receiving with the Furrion Vision S Wireless RV Backup Camera System part #FOS43TASF is due to an interruption on the camera's power wire. Make sure that the camera is receiving…

view full answer...

Answer 10

In order to un-pair the camera on your Furrion RV Observation System #FOS05TASF and assign it to the correct designation you will first just need to press the button at the bottom of the camera itself and hold it down for 15 seconds. This will…

view full answer...

Answer 11

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...