Working Load Limit Weight Capacity of Brophy Tie Down Anchors # RR6K-4

Question

Question:

Im sure you get these questions a ton I apologize in advance. Going in enclosed car trailer. My car fully fueled and outfitted will be 3900 pounds. My math says i can put up to a 8000 pound car on these rings off working load. Is this correct? Thank you!

asked by: Mike K

0

Expert Reply:

Yes, you are correct. If you used all 4 of the D-rings of the Brophy Tie Down Anchors # RR6K-4 you'd have a safe working load limit created by them of 8,000 lbs. This would be more than enough for your car that weighs 3,900 lbs.

expert reply by: Jameson C

0

Answer 1

You are correct. You will want to use the backing plate to sandwich the boards and provide the most secure connection when installing the Brophy Swiveling D-Ring Anchors #RR6K-4 . You can mount these in a recessed hole created by a router or punch…

view full answer...

Answer 2

The Brophy Swiveling D-Ring Anchors w Backing Plates and Hardware - Bolt-On - 2,000 lbs - Qty 4 #RR6K-4 are a great choice if you're in need of fixed points on the floor of the trailer and don't care much about flexibility of spacing for…

view full answer...

Answer 3

To secure vehicles in your 16 foot car hauler, I recommend using the Erickson Adjustable Ratcheting Wheel Net w/ Hooks #EM58522. These will fit 14 inch to 29 inch tires and includes 2 inch cam buckles to allow the webbing to be shortened or…

view full answer...

Answer 4

I am happy to tell you that four of the Stake Pocket Tie-Down Anchor - Black Powder Coat - 2" D-Ring - 1,600 lbs #T55B that you ordered will indeed be strong enough to handle the 4,400 lb car you are going to haul. The working load limit (WLL)…

view full answer...

Answer 5

I can absolutely help you and make a recommendation. The floor of your Big Tex 70 car trailer is an 1/8 diamond steel plate. The 1/8 plate will be fine for a tie down point for anything but a car. You need a bracket not to fasten something down tight…

view full answer...

Answer 6

The best option we have for you to add additional tie-downs to your car hauler would be to use Brophy D-Ring Tie Down Anchors part #RR5K. You could weld the top plate to the diamond plate flooring or you could drill a few holes and use the included…

view full answer...

Answer 7

The Brophy Swiveling D-Ring Tie Down Anchor part #RR06 with the Backing Plate for RR06 Recessed Swivel D-Ring Tie Down part #BP06 are a great, easy to install set of tie-downs which can be used for securing a vehicle. The tie-downs themselves have a…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...