Availability of DeeZee Paddle Handle Latch Lock That Allows Removal of Key When Unlocked

Question

Question:

Looking for a lock that you dont have to lock in order to take the key out. The one we have now you have to lock in order to remove the key

asked by: Walker T

0

Expert Reply:

My contact at Dee Zee said they do not offer a paddle handle latch lock for their toolboxes that allow removal of the key with the lock unlocked. But we do have non-locking handles such as # UWSNONLOCKING. I measured this item and the part # DZTBLATCH1 and both have the same mounting hole dimensions which are shown on the linked photo.

expert reply by: Adam R

0

click to enlarge

Answer 1

The Replacement Non-Locking Paddle Handle for UWS Toolboxes #UWSNONLOCKING only comes with the handle. You will need to source rivets locally to install this on your toolbox.

view full answer...

Answer 2

The Replacement Non-Locking Paddle Handle for UWS Toolboxes part #UWSNONLOCKING is polished stainless steel.

view full answer...

Answer 3

I checked with UWS and the closest non-locking version of the Replacement Lock Handle #UWS003-SLLKBLK available is the Replacement Non-Locking Paddle Handle #UWSNONLOCKING. This polished stainless steel lock works with many UWS toolboxes and its…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area…

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Availability of DeeZee Paddle Handle Latch Lock That Allows Removal of Key When Unlocked

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching