Dimensions of Draw-Tite 2-5/16 Inch Hitch Ball

Question

Question:

What is the ball dimensions including the height extending above the mounting plate? I will be using the 2-5/16inch ball for a locking mechanism for my trailer coupler.

asked by: Will C

1

Helpful Expert Reply:

Some dimensions of the 2-5/16 inch hitch ball # 19286 are shown in the attached diagram. The shank is 1-1/4 inches in diameter and is 2-3/4 inches long. Overall it's about 6 inches tall, aboput 3 inches of that being from the bottom of the base to the top.

expert reply by: Charles S

1

click to enlarge

Answer 1

For a trailer that has an angle iron frame like what you have what I would recommend is a system like the Reese Steadi-Flex part #RP66558 you referenced and have the outer brackets welded to the frame of the trailer since there isn't a clamp on…

view full answer...

Answer 2

Hey Wolf, since your 2008 Dodge Sprinter has a 7-way already what you would need to install the Redarc Tow Pro Elite part #RED44FR would be the part #5506 which comes with the wiring needed to wire in the brake controller to an already installed…

view full answer...

Answer 3

I would recommend that Blue Ox TrackPro #BLU77FR simply because it does not have lift chains like the SwayPro #BXW1006. Both will do a great job but the TrackPro will have a little less movement because of the absence of drop chains. Blue Ox is a…

view full answer...

Answer 4

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 5

You are definitely on the right track here. When it comes to weight distribution hitches, it all comes down to your tongue weight. All of these systems will have a range of tongue weights that you want to stay within for them to work effectively. I…

view full answer...

Answer 6

Pertaining to the Reese Pro Round Bar Weight Distribution Hitch #RE34FR, the head itself without a ball is about 20 lbs. The shank is about 25 lbs. The ball itself would be 3 lbs. Each spring bar is about 12 lbs apiece.

view full answer...

Answer 7

The Husky Center Line Weight Distribution with Sway Control 32217 is for 600 lb to 800 lb total tongue weight capacities (the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 10

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Dimensions of Draw-Tite 2-5/16 Inch Hitch Ball

Product Page this Question was Asked From

Continue Researching