Replacement Safety Chain U-Bolt Recommendation for B and W Gooseneck Hitch

Question

Question:

I would like to know if the u bolts are the same for the companion as the safety chain u bolts . I need the companion u bolts

asked by: Steven D

0

Expert Reply:

Sounds like you are in need of replacement safety chain U-bolts for your B and W Turnoverball gooseneck hitch. For that we have them as part # BW1900-2-1600.

expert reply by: Jameson C

0

Answer 1

The RVK3000 is an older version of the B&amp;W Companion hitch part #BWRVK3500 that you also mentioned. Both of these hitches were designed to fit the Turnoverball gooseneck hitches so yes, the RVK3000 would fit one too.

view full answer...

Answer 2

Yes, the B and W Companion base part #BWRVB3500 does work with all Turnoverball gooseneck hitches. This is just the base. For a complete hitch you&#39;d need the part #BWRVK3500.

view full answer...

Answer 3

I attached a link to the install instructions for the B and W Companion Hitch part #BWRVK3500 you referenced plus attached a review video that walks you through the install process. You would basically just need to reverse the steps in the video.…

view full answer...

Answer 4

I have a solution but the gooseneck attachment point for the turnover ball systems isn&#39;t available for individual sale. You will need to purchase the Replacement Base for B&amp;W Companion 5th Wheel Trailer Hitch - 20,000 lbs…

view full answer...

Answer 5

Yes, the gooseneck hitch balls for the factory prep packages are the same for Ram and Ford. If you need a new hitch ball for either of these systems than you can use the Curt Pop-In Ball part #C60601 or the Reese Pop-In Ball part #RP19311.

view full answer...

Answer 6

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory…

view full answer...

Answer 7

I do have a solution, but since Lance has their own plug design there are no adapters that will work, including the #47595. The best option is to replace the lance plug with a standard 7-way blade connector like the #PK12706. This will eliminate…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that&#39;s going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 11

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the…

view full answer...

Answer 12

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Replacement Safety Chain U-Bolt Recommendation for B and W Gooseneck Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching