Replacement 1157 Bulb for Wesbar Submersible Low Profile Trailer Tail Lights

Question

Question:

replace the BULB in a west bar 102641

asked by: Dick

0

Expert Reply:

If you have the Wesbar Submersible Low Profile Trailer Tail Lights # 403026 and # 403076 on your trailer, which the replacement lens # 102641 fits, then the correct replacement bulb is the 1157 part # A1157B on our site.

If you would like to replace them with red LED bulbs then we also have part # P231157R360 that you can use.

expert reply by: Jon G

0

Answer 1

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable. If your capsule is sealed, then your best option is to replace the lights with new lights like part #403026 and…

view full answer...

Answer 2

It sounds like you are trying to remove your older Wesbar Submersible Low Profile Trailer Tail Light from your Ranger Trail boat trailer. These lights are held on to the trailer with 2 studs on the back of the light housing. To remove the lights,…

view full answer...

Answer 3

I checked with Wesbar and the lens only for the LED version of the tail lights you have is not available as a separate part but you can replace the light with #271595 for the left side of the trailer and #271594 for the right side.

view full answer...

Answer 4

SAE stands for the Society of Automotive Engineers. The SAE part number is not the part number of the light, it is just a number on the lens that means that lens has passed SAE guidelines. In order to try and locate a replacement lens for you, I will…

view full answer...

Answer 5

For an LED replacement that is nearly identical to the Wesbar 105826 light you can use #STL36RB for the right side and #STL37RB for the left side. There are also versions that have a plug instead of just bare wires. For the right side use #STL36RPG…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Can I see a picture of the assembly you are refering to? I can't find any info on it.

view full answer...

Answer 8

Typically the only thing that limits a trailers speed rating is the tires, so replacing the tires with ones that have a higher speed rating is likely all you need. Based on the information I could find on your 40x48 Ironton Utility Trailer it uses…

view full answer...

Answer 9

To upgrade your lights, an exact replacement won't really be possibly but retrofitting an upgraded LED option will be super easy. For this, I recommend the Dual LED Trailer Tail Light - Stop, Turn, Tail, Backup - Red and Clear Lens#CE86FR by…

view full answer...

Answer 10

One main difference between LED lights and incandescents is the amount of power each one draws. I did a little research and found that if you were to have LEDs and incandescents on the same circuit, it would be too much power draw for the LEDs…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Replacement 1157 Bulb for Wesbar Submersible Low Profile Trailer Tail Lights

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching