Replacement Parts for Stromberg Carlson Landing Gear Legs

Question

Question:

Can I purchase just the Jack Nut 911-10? If so how? Thanks,

asked by: William

0

Expert Reply:

I spoke with my contact at Stromberg Carlson and they do not offer the Jack Nut 911-10 as a replacement part. Therefore, your only option would be to replace the entire landing gear leg. I have attached these replacement options for you as well. There is a repair kit available, the Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146059 for lead and part # LG-146060 for follow but it does not include the jack nut.

Replacement Lead Leg for Stromberg Carlson Landing Gear - 33-1/2" - part # LG-177202
Replacement Follow Leg for Stromberg Carlson Landing Gear - 33-1/2" - part # LG-177201
Replacement Lead Jack for Stromberg Carlson Landing Gear - 29-1/2"- part # LG-179013
Replacement Follow Jack for Stromberg Carlson Landing Gear - 29-1/2" - part # LG-179014

expert reply by: Conner L

0

Answer 1

The Lead Jack Repair Kit #LG-146059 that contains the drive pin 920-00 that you referenced comes in a kit and isn't available as separate parts unfortunately. To get the replacement drive pin you will need to get the whole kit.

view full answer...

Answer 2

I spoke with my contact at Stromberg Carlson and unfortunately the Acme Jack Nut 911-10 is not available as a replacement part. The only option is to replace the landing gear leg. I am not sure which leg needs to be replaced or which landing gear you…

view full answer...

Answer 3

I attached a diagram that shows how the Lippert Components Venture Lead Leg Repair Kit #LG-146059 installs.

view full answer...

Answer 4

The overall dimension you are measuring is the length of the outer tube of the jack. If you check out the first picture I attached you'll see where the part #LG-1 measures 29-1/2 inches in length. The second picture I attached shows the…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Replacement Parts for Stromberg Carlson Landing Gear Legs

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching