Will Curt Hook With Spring Loaded Safety Latch Work With 3/8" Safety Chain

Question

Question:

will a 3/8 inch safety chain slip on this hook?

asked by: Jeff B

0

Expert Reply:

As you can see by the accompanying diagram the narrowest part of the Curt Hook with Spring Loaded Safety Latch for Safety Chains and Cables # C81288 is 5/8" so a 3/8" safety chain will work with this hook.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The narrowest portion of the #C81288 that you referenced where a cable would have to pass through is 5/8 inches.

view full answer...

Answer 2

Using the term 'Proof' when describing chain is a descriptor of its weight rating and its construction. A grade 30 or 30 proof chain is for a general purpose application that doesn't require a great amount of strength. A grade…

view full answer...

Answer 3

I went and pulled the Curt Hook with Spring Loaded Safety Latch #C81288 from our warehouse to measure it for you. Check out the picture I attached to see all of the dimensions.

view full answer...

Answer 4

Since the Curt S-Hook with Wire Keeper for Safety Chains and Cables, part #C81820 is made of 7/16 inch diameter zinc coated steel, I recommend using something like a vise or channel locks if available to crimp the end around your safety chains. If…

view full answer...

Answer 5

The plug that is on the Black Bracket and Single Wire Plug #A65PB is designed for trailers that already have the type of plug-in wiring on the trailer (Plug-n-Go). The wiring that plugs into this end is not available but an auto parts store or…

view full answer...

Answer 6

For your safety chains I recommend the Curt Hook with Spring Loaded Safety Latch for Safety Chains and Cables #C81288 which have a weight capacity of 5000lbs each making them perfect for your trailer that weighs in at 6500lbs. The #C81288 is sold in…

view full answer...

Answer 7

I would be happy to help! The correct replacement Clevis hooks will be dependent on the thickness of your chain links. Likely you would need either the Curt Clevis Hook with Spring Loaded Safety Latch - 7/16" #C81970 which fits 7/16" Thick…

view full answer...

Answer 8

For roof vents like what you sent in a picture of we recommend the Install Kit part #344270KITW. They don't make gaskets but this sealant will provide you with a way to seal up the vent and has install screws that you could use or not.

view full answer...

Answer 9

Ventline produces most of the trailer/RV roof vents supplied as OEM parts so our replacement parts selection should have you covered. If you can find a Ventline part number on your vent base this will help confirm which parts you need in case those…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Will Curt Hook With Spring Loaded Safety Latch Work With 3/8" Safety Chain

Product Page this Question was Asked From

Continue Researching