Where to Mount the Linxup GPS Tracking Device on a Dump Trailer

Question

Question:

What would be the best location for installing tracker.

asked by: Luis

0

Expert Reply:

The best location to install the Linxup GPS Tracking Device part # 300-AT3-S is subjective. The box is weather proof so you don't need to worry about it getting wet or dirty. It will however need access to power so that is something you will need to be aware of when mounting.

Since you have a dump trailer, I would refrain from any moving parts. The best spot for most trailers is going to be on the inside of the frame rail near the battery because it is out of site and still has relatively easy access to power. It comes with the bolts you need to mount the box.

expert reply by: Conner L

0

Answer 1

We have exactly what you are needing for your 5th wheel! The Linxup GPS Tracking Device w/ 4G Service #300-AT3-S is a GPS tracker that is hardwired in and includes 1 Year of 4G network tracking service. This will be a great choice for a GPS tracker…

view full answer...

Answer 2

Thanks for the picture of your Texas Pride Gooseneck. Based on that we know that the coupler lock part #BLTL-53-40D2 will fit and work great.

view full answer...

Answer 3

Any vehicle that uses any brand and type of tire chain should be operated at reduced speeds. If road conditions merit use of chains then they also merit reduced driving speeds, typically 30-mph for most vehicles and most chains. The two linked…

view full answer...

Answer 4

Some states do require tire chains on trailers especially for braked axles. They're commonly called drag chains in this application. As long as you have the internal clearance needed for the chains, you can use them on trailer tires. The…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

According to our FAQ on slipper springs, linked for referenced, the torque specs are as follows: Torque Ratings 1/2 inch Bolts: 45 ft/lbs - 70 ft/lbs 9/16 inch Bolts: 65 ft/lbs - 95 ft/lbs 5/8 inch Bolts: 100 ft/lbs - 120 ft/lbs The Replacement…

view full answer...

Answer 7

When the battery dies on the Galeo Pro GPS Tracking Device #GA94FR you have to replace the sensor as they do not offer a replacement battery. The battery is hardwired into the unit and not something that can be replaced.

view full answer...

Answer 8

The Linxup GPS tracking device #300-AT3 is just the device by itself. It does not come with the service. This would allow you to choose what type of service you want: month to month, yearly. The other one, #300-AT3-S, is the device plus 1 year of…

view full answer...

Answer 9

The Linxup GPS Tracking Device - 3-3/4" Long x 2" Wide x 1" Tall #300-AT3 will absolutely work with the car batteries but it can store up to 3 months battery power on its own if you want to mount it on units without a…

view full answer...

Answer 10

I attached pictures that show how the switches of the Bulldog Powered Jack #BD500187 get wired.

view full answer...

Answer 11

The Galeo Pro GPS Tracking Device #GA94FR will need the tracking service plan to tell you where the vehicle is. The service plan is what allows the device to communicate over cell service its exact position.

view full answer...

Answer 12

If by serial number you mean VIN and the trailer manufacturer is still in business then yes, you would likely be able to obtain the bearing numbers from the manufacturer. If none of the above are true, then the only other way to determine which…

view full answer...

Where to Mount the Linxup GPS Tracking Device on a Dump Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching