Parts Needed to Install All Stainless EOH Disc Brake Components on Trailer with 3,500 Axles
Question:
I have a 2006 Polar MagicTilt trailer with the factory surge 10inch disks on one axle. I would like to convert it to an all stainless system with disks on both of the tandem axles. 3500# axles. The idler axle has the brake mounting plates. I would like to go to electric over hydraulic. My 2012 F350 has EOH mode in the factory controller. Current brakes are Kodiak plain steel. Is there a kit available with all parts, rotors/hubs, calipers bearing and seals? If not what parts would you suggest? Thanks
asked by: Harry C
Expert Reply:
For the idler hub axle the easiest way to add stainless disc brakes would be a slip on kit like part # K2R35S which has rotors that would slip right over the current hubs and comes with everything else needed to install. To convert the hubs too of this axle to stainless you'd also need the part # KH84545S.
Using the hub # KH84545S with the slip on disc kit part # K2R35S with it would be your best option for your current brake axle too since it's the only way to get everything stainless.
Then for an electric over hydraulic actuator our best option is the Hydrastar kit part # HBA16. We recommend this kit the highest as it's the most reliable and best performing option we offer.
Products Referenced in This Question
Hydrastar Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Brake Actuator
- Electric-Hydraulic Brake Actuator
- 1600 psi
- Disc Brakes
- Hydrastar
more information >
Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Stainless Steel
- Trailer Hubs and Drums
- Hub
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Kodiak
more information >
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Stainless Steel - 3,500 lbs
- Trailer Brakes
- Disc Brakes
- Marine Grade
- 5 on 4-1/2 Inch
- Rotor
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Kodiak
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Kodiak Trailer Hubs and Drums - Hub - KH84545S Review
- Q&A: Bearing and Seal Recommendation for Installing Kodiak Hub KH84545S on MFI/Yamaha Trailer
- Shop: Hollywood Racks Safety LED Light Bar for Bike Racks
- Search Results: heavy duty spare tire carrier
- Shop: Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Stainless Steel
- Shop: Kodiak Ceramic Brake Pads w/Stainless Steel Backing Plate - 3,500 lbs to 6,000 lbs
- Shop: DeeMaxx Stainless Steel Drive-In Grease Cap w/ Plug - 1.98" Outer Diameter
- Shop: TireMinder Tire Pressure Gauge - Digital - 5 to 150 psi
- Shop: Kodiak Trailer Wheel Lug Nut - Stainless Steel - 1/2" - Qty 1
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Q&A: Correct Bearing Kit for 2019 Jayco North Point 315RLTS
- Shop: Trailer Hitch
- Article: Most Popular Wheel Bearings
- Search Results: 25580
- Shop: Trailer Wiring
- Search Results: lug nut
- Article: Trailer Tire Sizing
- Video: Hollywood Racks LED Light Bar Review
- Video: Dexter Nev-R-Adjust Electric Trailer Brake Kit Installation - 5th Wheel
- Article: Tire TLC: How & When to Check Your RV/Trailer Tire Pressure
- Search Results: bk2~100
- Shop: Brake Controller
- Search Results: lug nuts
- Search Results: grease cap
- Shop: Suspension Enhancement
- Q&A: Stainless Steel Disc Brake Kit Solution for 3,500 lb Axle of Single Axle Boat Trailer
- Q&A: Determining Which Kodiak Slip On Disc Brakes Fit 2021 Load Rite Trailer W/ 3700lb Axles
- Article: How to Bleed Your Trailer Surge Brakes
- Q&A: Recommended Hitch for a 2024 Jeep Grand Cherokee L
- Q&A: Replacement Hub and Brake Assemblies that Fit Sure Trac 3,500 lb Axle