Gooseneck Hitch Ball and Tow Loop Recommendation for 2019 Ford F-250

Question

Question:

I have a 2019 Ford F-250 with the pucks in the bed of the truck and I need the gooseneck ball and safety chain loops to tow a trailer.

asked by: Walter

0

Expert Reply:

For your 2019 Ford F-250 with the factory rail kit installed you'll want the Curt gooseneck ball and safety chain loops part # C60692. This kit has the easiest to use ball and safety chain loops that are the easiest to attach to as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

On Reese Goose Box #RP85FR from the bottom of the coupler portion to the bottom of the pin box body at the back where it attaches to the trailer's wings measures approximately 15-1/2 inches. The distance from the center of the coupler…

view full answer...

Answer 2

I recommend using the B&W Ball and Safety Chain Kit #BWGNXA2061 for the factory puck system on your 2020 Ford F-350 Super Duty. I like this kit of the Curt #C60692 and Reese #RP30137 options because it uses a handle to secure the gooseneck…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Answer 8

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…

view full answer...

Answer 9

The weight is 54 lbs for the Superwinch S7500 Trailer Winch #SW1475201.

view full answer...

Answer 10

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...

Answer 11

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 12

The 07100 bearing number you referenced is an older bearing that has the same dimensions as #L44643. If both the inner and outer bearings on your existing trailer are the 07100/ #L44643, and the hub has a 4 on 4 inch bolt pattern, the correct…

view full answer...