One Electric Trailer Brake Assembly Does Not Release After Applying Brakes
Question:
I replaced old brakes 10inch x 2 1/4 with dexter assemblies. Drums look fine. All brakes engage but 1 will not release until I turn the drum back. Theres a click and brake is free. All wheels are adjusted the same as far as I can tell. I think it is hanging up on the top anchor pin. Any suggestions?
asked by: Don T
Expert Reply:
You may be right. I would remove the assembly and check that all the components are in working order. See if you can get it to do the same thing while off the trailer by manipulating the various moving parts.
Some of the parts may need to be properly lubricated but do not get any grease on the pads. You could also have a magnet or wiring issue that is causing the magnet to stick. You can test the magnet by itself to see if it is faulty. I have included a link to an FAQ article that explains how to go about testing a magnet. You will need a multimeter like # PT89ZR if you do not already have one.
You can also test the wiring to the magnet. Make sure the ground is connected to a clean bare metal surface and that the power wire is intact to the trailer connector. If you can hear the brake hum after releasing the brakes that would indicate that the magnet is still receiving power and there is probably a short circuit somewhere or a bad magnet.
Products Referenced in This Question
Digital Multimeter with 42" Long Test Leads - LED Display
- Electrical Tools
- Testers
- Multimeter
- Yellow
- Performance Tool
more information >
Product Page this Question was Asked From
Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 3500 lbs
- Brake Assembly
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Dometic 320 Full-Timer RV Toilet - Standard Height - Elongated Bowl - White Ceramic
- Q&A: Troubleshooting Trailer Brakes That Won't Release
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 5 Bolt Flange - 7,000 lbs
- Shop: Optronics 12V LED RV Dome Light - Double - 10-5/16" Long x 4-3/16" Wide - White Housing
- Shop: 12V RV LED Puck Light - Surface Mount - 4-1/2" Long - White Housing
- Shop: LED RV Utility Light - Weatherproof - 95 Lumens - Chrome Trim - Clear Lens
- Shop: 12V LED RV Dome Light - Single - 3" Long - Chrome Trim
- Shop: RV Exterior Lighting
- Shop: RV Interior Lighting
- Video: Command Electronics RV Lighting - Utility Light - 328-003-1400W Review
- Search Results: tarp kit
- Shop: Aluminum Liger Trailer Wheel - 16" x 6" Rim - 8 on 6-1/2 - Glossy Black
- Search Results: brkh10b
- Search Results: timbren
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Shop: Trailer Wiring
- Q&A: What is the Overall Width and Diameter of a 235/80R16 Size Tire
- Q&A: What is the Diameter and Thread Pitch of the Mounting Hardware for 10" Brake Assemblies # BRKH10B?
- Search Results: redarc
- Video: Review of Dexter Trailer Brakes - Electric Drum Brakes - K23-478-479
- Video: Review of Dexter Axle Trailer Brakes - Electric Drum Brakes - DX52QR
- Video: Review of Dexter Trailer Brakes - Electric Drum Brakes - K23-462-463-00
- Q&A: Troubleshooting Trailer Brakes Where One Wheel Locks Up
- Video: etrailer Electric Trailer Brake Kit Review and Installation
- Video: Redline Trailer Brakes BRKH10B Review
- Article: Testing Trailer Brake Magnets for Proper Function
- Q&A: Power To Trailer Brake Magnets But Brakes Are Not Engaging
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: How to Charge a Trailer Battery While Driving: 3 Common Problems (And How to Fix Them)
on Accessories and Parts
