Replacement Head for Curt TruTrack Weight Distribution System # C17500

Question

Question:

Is there a way that you can just purchase the head of the Curt system? I have the complete 10000 lb system now, but the holes on the head have been damaged.

asked by: Jeremy T

0

Expert Reply:

We have exactly what you need!

For just the head of the Curt TruTrack Weight Distribution System # C17500 you will use part # C17507. This is an exact replacement for the 10,000 pound system and will work perfectly. I have attached a short video demonstration that you can check out as well.

expert reply by: Chris R

0

Answer 1

A chrome finish ball #C40036 is going to look good but it will not be corrosion resistant. A ball with a machine finish like #C40087 , is going to have about the same corrosion resistance. In terms of performance they will wear at about the same rate…

view full answer...

Answer 2

You can piece out the Curt TruTrack Weight Distribution System #C17500 with the following part numbers that include everything but the shank: Trunnion Spring Bar - #C17536 (need 2 of these) Spring Bar Lift Tool - #C17512 Frame Brackets - #C17508…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 10

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

Hey Dennis, we have a replacement 7-way plug with the part #A7WCB which would work great to replace your damaged one. I attached a diagram for 7-ways for you to check out as well.

view full answer...

Replacement Head for Curt TruTrack Weight Distribution System # C17500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching