Does Air Line of Bulldog Winch Compressor # BDW41000 Use Standard Quick Connect Fitting

Question

Question:

Are the connectors on the Bulldog Winch BDW41000 STANDARD and can I use an Extension hose to reach the trailer tires?

asked by: Brian K

0

Expert Reply:

The air hose of the Bulldog Winch Compressor # BDW41000 has a standard quick-connect fitting on the end of it so if you had an extension hose that fit that style of fitting this would work well for you.

expert reply by: Jameson C

0

Answer 1

There are a couple of air compressors I recommend for inflating your large RV tires up to 100 psi, both from Bulldog Winch. These are portable compressors (both of which come with a carry bag) that connect to a 12v battery for power and will do a…

view full answer...

Answer 2

The hose of the Bulldog Winch Compressor #BDW41000 that you referenced attaches to the compressor with standard quick connect fittings seen on most compressors. If you wanted to add hose to this you pretty easily could with standard compressor hose.

view full answer...

Answer 3

The blocks on the TorkLift StableLoad #TLA7202 are 2-1/2" tall.

view full answer...

Answer 4

You are going to want to trim the block down about an inch. We have seen this issue before on similar GMC trucks and if you don't trim the block down the suspension is going to feel incredibly rough. If you trim about an inch off and match the…

view full answer...

Answer 5

The Torklift StableLoad Suspension Upgrade #TLA7202 is a great option for improving the handling and reducing side-to-side sway on your 2017 GMC Sierra 3500 Denali when your truck camper is attached. These will simply bolt onto each frame-mounted…

view full answer...

Answer 6

The TorkLift StableLoad Suspension Upgrade Kit #TLA7202 installs WITHOUT drilling or trimming on vehicles with factory leaf springs and an upper overload spring. The four springs install in place of your factory bump stops. Written installation…

view full answer...

Answer 7

The TorkLift StableLoad Suspension Upgrade #TLA7202 is a great option for your 2019 GMC Sierra 3500 as it is designed for trucks that have factory leaf springs and an upper overload spring. The StableLoad Suspension Upgrade is going to help reduce…

view full answer...

Answer 8

If your suspension is going up and down 2-3 times after hitting a bump you most likely need to replace the shocks of your truck. That will slow the rebound down quite a bit and should prevent the suspension from basically bouncing like you described.…

view full answer...

Answer 9

I reached out to both Firestone and Air-Lift and confirmed that the air helper spring kit you have on your 2002 Chevrolet Silverado is the Air Lift Ride Control Air Helper Springs - Rear Axle #AL59501, but unfortunately the air springs for this kit…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

I wish I could say yes, but as of right now they are not a fit for the 2016 models and we do not have any other suspension enhancement options. If you are trying to fight suspension sag from the tongue weight of a trailer there is a better option. A…

view full answer...

Does Air Line of Bulldog Winch Compressor # BDW41000 Use Standard Quick Connect Fitting

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching