What are the Base Dimensions of the Dutton-Lainson Hand Trailer Winch Model DL2000AB

Question

Question:

what are the base dimensions for this prodcut DL14730. Specifically how wide is the base.

asked by: Robert R

0

Expert Reply:

The overall width of the Dutton Lainson Winch, # DL14730, is 4-3/4 inches. The height from the bottom of the base to the top of the drum is 6-53/64 inches. And the length front to back is 6-1/4 inches, 8-27/32 inches including the drum.

expert reply by: Michael H

0

Answer 1

From what I have found, the Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed - 1,800 lbs #DL14627 will match the bolt pattern of your Shelby 5407B. I have attached a diagram as well as the dimensional drawing showing the bolt pattern on…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

To replace your 1,700 lb Shelby 5407B winch I recommend the Dutton-Lainson Single Speed Winch #DL14627 which is rated for 1,800 lbs. This winch features permanently lubricated bearings, high carbon steel gears, and a Zinc TUFFPLATE finish for…

view full answer...

Answer 11

Hey there Zack, appreciate that info, and we do not offer an axle of that length, and they can be pretty tricky to find. Sometimes people will have to get their axles custom-fabricated at a local fabricator, but I do have an option to consider, which…

view full answer...

Answer 12

Thanks for the picture! While we do not have an exact replacement for a Profile 2000 winch we do recommend the Dutton-Lainson Hand Winch item #DL14627 as a replacement. This winch has an 1,800 lbs capacity and will work great with the 20' x…

view full answer...

What are the Base Dimensions of the Dutton-Lainson Hand Trailer Winch Model DL2000AB

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching