Winch Base Width Dimensions and Bolt Hole Pattern for the Freewheeling Brake Winch # DL14996

Question

Question:

What are the dimensions for the brake winch? Specifically the total width of the plate which attaches to the device?

asked by: Robert R

0

Expert Reply:

I attached a drawing showing all of the dimensions for the base of the Dutton-Lainson Freewheeling Brake Winch, # DL14996, for you to review, see link.

The overall width of the base, including the curve created by the bend in the plate, adds up to 4-3/4 inches and the overall length of the base is 5-1/2 inches.

expert reply by: Robert G

0

click to enlarge

Answer 1

While we don't have a repair kit for your Shelby 5352 winch we do have a great replacement winch to match what you have since it is a 1,500 lb brake winch. For that you'd want the Dutton Lainson 1,500 lb Winch Part #DL14996 which would be a…

view full answer...

Answer 2

The discontinued Shelby 5407 is a single-speed, 1,700 lb hand winch, and we can get you a replacement with a higher capacity. The best option for that is a winch from Dutton-Lainson: - Dutton-Lainson Hand Winch #DL14881 The #DL14881 is a 3,500 lb…

view full answer...

Answer 3

Yes, the 60-Degree angle of the 1/2"-20 DeeMaxx Trailer Wheel Lug Nut #DE93GR is standard for the vast majority of trailer wheels out there. There are some 90-Degree cone shapes but these are typically for 5/8" and 9/16" wheel bolts so…

view full answer...

Answer 4

A 19 mm socket would be needed to remove the DeeMaxx Lug Nut part #DE93GR.

view full answer...

Answer 5

Torsion axles use internal rubber cords to provide the suspension motion and they really are not practical to repair/rebuild. Certainly any axle that was damaged in an accident should be replaced purely for safety reasons. It is potentially possible…

view full answer...

Answer 6

Some Shelby winch models used a handle that secured to the winch with an Allen key. If this is the type you have then it is possible that the set screw or the post on the winch the handle attaches to is stripped or worn to the point that the handle…

view full answer...

Answer 7

From the pictures you sent in it looks like the inner diameter of your Nev-R-Lube bearing is about 2" which means you'd need the 50MM Nev-R-Lube Bearing for 8,000-lb Dexter Axles #31-71-3. Aside from that you're basically just going to…

view full answer...

Answer 8

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 referenced in your question do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life…

view full answer...

Answer 9

The Shelby winch part #5351 that you mentioned is no longer available but it was a 1,000 lb winch with a 2 way ratchet. Dutton Lainson actually bought Shelby so the most similar winch would probably be the Dutton Lainson part #DL14934 which is a…

view full answer...

Answer 10

I have attached for you below a dimensional drawing of the Dutton-Lainson Hand Winch with Automatic Brake part #DL14934 which you can then use to determine fit and compatibility. I am not sure how your existing winch is setup but you can use the…

view full answer...

Answer 11

We have a left handed winches like the part #DL15403 which has a 2,500 lb capacity or the part #DL16331 which is lower rated 1,2000 lbs.

view full answer...

Winch Base Width Dimensions and Bolt Hole Pattern for the Freewheeling Brake Winch # DL14996

Product Page this Question was Asked From

Continue Researching