Possible Replacement Step Pad for 2012 Chevy Silverado

Question

Question:

I have a set of bars they are 4 oval 24x4 pads with 6 pins they are on a 2012 Silverado with the American luxury coach package

asked by: Bruce G

1

Helpful Expert Reply:

What you sent in a picture of looks very similar to the # 21-0001 that you referenced. Check out the dimension picture I attached and compare it to the dimensions of your step pad.

expert reply by: Jameson C

1

click to enlarge

Answer 1

With 5 holes, you most likely have Westin nerf bars. I recommend the Replacement Step Pad for Westin Platinum Series Oval Nerf Bars - Front/Rear - Qty 1 #21-0001 which are 24 inches by 4 inches.

view full answer...

Answer 2

The closest possible match to what you are looking for is the Westin Platinum step pad part #21-0001 that you referenced. It's 24 inches long like you need and has 6 posts for attaching to the step bar. So what you'll need to do is check out…

view full answer...

Answer 3

We do have one replacement step pad from Westin with the part #21-0001 that matches the 24 inch length and 4 inch width of your existing pads. The pad also features 6 mounting posts like you mentioned. In order to see if this will work on your nerf…

view full answer...

Answer 4

We do carry replacement pads for Westin and Bully nerf bars, but to be a good fit for your 2011 Ford F-350 truck, you will need to measure the pad you wish to replace. I have attached 2 photos of one of the replacement pads we offer, part #25-0001.…

view full answer...

Answer 5

It sounds like you need the Replacement Step Pad for Westin Platinum Series Oval Nerf Bars - Front/Rear - Qty 1 #21-0001. You can see the measurements in the photo and that there are 6 pegs, but only 5 of them use the clips to hold the pads in place.…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Possible Replacement Step Pad for 2012 Chevy Silverado

Product Page this Question was Asked From

Continue Researching