Replacement Step Pads With 5 Studs That Are 24 inches long

Question

Question:

Got a new truck , but dont know the make of the bars on the truck.i do know that the pads now have five holes for new step pads and old pad was 24inches long.can you help?

asked by: Bob

0

Expert Reply:

With 5 holes, you most likely have Westin nerf bars. I recommend the Replacement Step Pad for Westin Platinum Series Oval Nerf Bars - Front/Rear - Qty 1 # 21-0001 which are 24 inches by 4 inches.

expert reply by: Jason S

0

click to enlarge

Answer 1

It sounds like you need the Replacement Step Pad for Westin Platinum Series Oval Nerf Bars - Front/Rear - Qty 1 #21-0001. You can see the measurements in the photo and that there are 6 pegs, but only 5 of them use the clips to hold the pads in place.…

view full answer...

Answer 2

Thank you for those dimensions, and I think we may have what you need for your Tacoma with the following part: - Replacement Step Pad for Westin Platinum Series Oval Nerf Bars #21-0001 I have added a photo with the measurements of this replacement…

view full answer...

Answer 3

The closest possible match to what you are looking for is the Westin Platinum step pad part #21-0001 that you referenced. It's 24 inches long like you need and has 6 posts for attaching to the step bar. So what you'll need to do is check out…

view full answer...

Answer 4

What you sent in a picture of looks very similar to the #21-0001 that you referenced. Check out the dimension picture I attached and compare it to the dimensions of your step pad.

view full answer...

Answer 5

We do have one replacement step pad from Westin with the part #21-0001 that matches the 24 inch length and 4 inch width of your existing pads. The pad also features 6 mounting posts like you mentioned. In order to see if this will work on your nerf…

view full answer...

Answer 6

We do carry replacement pads for Westin and Bully nerf bars, but to be a good fit for your 2011 Ford F-350 truck, you will need to measure the pad you wish to replace. I have attached 2 photos of one of the replacement pads we offer, part #25-0001.…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Replacement Step Pads With 5 Studs That Are 24 inches long

Product Page this Question was Asked From

Continue Researching