Are Kodiak Disc Brake Kits K250CP and K250CP-SS for Two Brake Assemblies

Question

Question:

Are your web prices per wheel or per axle?

asked by: John D

0

Expert Reply:

Parts # K250CP-SS and # K250CP are both two sets of pads, each enough to re-fit the two disc brake assemblies on one axle.

expert reply by: Adam R

0

Answer 1

We do not have a Kodiak disc brake caliper cross reference to automotive calipers but for the brake pads there are cross referenced parts. If you refer to the linked image you'll see a partial list of cross-compatibility of brake shoes for GM…

view full answer...

Answer 2

To replace just the brake pads for your Kodiak Disc Brake Kit #K2HR712E I recommend the Kodiak Brake Pads #K250CP-SS. These will work perfectly on your existing assemblies and the stainless steel backing plates will resist any corrosion over time. I…

view full answer...

Answer 3

For your 2007 Teton Homes Experience, I recommend the Kodiak Disc Brake Kit - 13" Hub/Rotor - 8 on 6-1/2 - Dacromet - 7,000 lbs #K2HR712D for the entire disc brake kit. For just the hub assemblies with rotors, I recommend the Kodiak 13" Hub…

view full answer...

Answer 4

The disc brake pads that we have for the Kodiak caliper that is marked 250 is the Kodiak Ceramic Brake Pads, part #K250CP, that you have referenced. These pads are for use on calipers that are rated for 7,000 lbs to 8,000 lbs. The D215 number is the…

view full answer...

Answer 5

The appropriate replacement brake pads for the Kodiak Disc Brake Kit #K2HR79E with the Kodiak 250 calipers are the Kodiak Ceramic Brake Pads for 7000-lb brakes #K250CP , which are designed for the 13" rotors in the #K2HR79E kit. There is also a…

view full answer...

Answer 6

The Kodiak Ceramic Brake Pads, #K250CP or #K250CP-SS, that you referenced can both be used to replace your current brake pads on your trailer's axles. The difference between the two is the #K250CP-SS disc brake pads have stainless steel backs.…

view full answer...

Answer 7

In order to get the correct replacement seal you will want to remove the seal from your hub and get the number stamped on it. If you can't find the number you can also use the dimensions of your seal to get the correct replacement. Get the outer…

view full answer...

Answer 8

You can use the Kodiak Ceramic Brake Pads #K250CP-SS to replace the worn pads on your Hydrastar Disc Brake Kit w/ Actuator for Triple Axle Trailers #HYD54FR.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Are Kodiak Disc Brake Kits K250CP and K250CP-SS for Two Brake Assemblies

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching