Dimensions of Westin Grille Guard Replacement Hardware Bracket

Question

Question:

hi, what are the dimensions of this bracket? length, both across the tee and down the tee, width or height, and steel thickness?

asked by: Gerald W

0

Expert Reply:

Take a look at the diagrams I made that show the measurements of the replacement bracket # 40-120PK. Also, the metal is around .233 inches thick.

This is the replacement bracket for the Sportsman Grille Guard # 45-1200.

expert reply by: Charles S

0

click to enlarge

Answer 1

It sounds like you're looking for a replacement installation kit for a Westin Sportsman Grille Guard that fits a 2009 Ford F-150. If so, the Replacement Mounting Kit for Westin Sportsman Grille Guard #40-250PK is the correct kit to install the…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

There's a few differences. • The Curt #C31017 is manufactured in the US, while the Draw-Tite #65046 is manufactured in Mexico. • When installed, the Curt hitch will sit higher on the vehicle for more ground clearance. The underside of the…

view full answer...

Answer 10

Let's start at the brake assemblies/hubs on your new gooseneck trailer. The two wires coming from each assembly look exactly as they should. One wire will ground to the trailer frame and the other wire will attach to the brake output wire. The…

view full answer...

Answer 11

Your slide-in truck camper does not have electric brakes so the blue brake circuit wire from its 7-way connector is not used. All other lighting functions as well as 12V auxiliary power will be maintained on the other circuits. Please refer to the…

view full answer...

Answer 12

I contacted my Curt Manufacturing rep, who tells me the total drop of their #C31017 is 4-1/4 inches. The drop is the distance from the top surface of the mounting flange that would sit flat against the underside of the frame members to the lowest…

view full answer...

Dimensions of Westin Grille Guard Replacement Hardware Bracket

Product Page this Question was Asked From

Continue Researching