Range Outside Vent Cover Dimensions and Compatibility with Lance Cabover

Question

Question:

Do you have one? Range outside vent cover 9 1/2 x 5 1/2 for lance cabover?

asked by: Rob

0

Expert Reply:

All of our current outside vent cover for RV range hood options are 11-1/2 inches by 5-1/2 inches outside dimension so they are a little wider than what you described. They fit a rough opening that is 10-1/2 inches wide by 3-3/4 inches. I've attached the link to all of our exterior wall vents for RV range hoods because the interior depth for each is different. I've attached a video of part # V2111-03 to assist. These may work for your camper with some minor modifications if the dimensions given were outside dimensions.

expert reply by: Jason S

0

Answer 1

The Clevis hook part #6495-401-04 that you referenced is standard enough size that it would work well on the hitch of your 2017 Ford F-250. I attached a picture for you to check out that shows the dimensions of the opening. The post that fits through…

view full answer...

Answer 2

Yes, the internal damper in the Ventline Exterior Wall Vents for RV Range Hoods, parts #V2111-55 in black and #V2111-13 in white, opens automatically when you turn on the exhaust fan in your RV's kitchen range hood. These vents also have a…

view full answer...

Answer 3

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The Carrier Air V RV Air Conditioner is no longer produced so a direct replacement of the same unit is not an option. However, we do have available the two Advent AC models that are designed as replacement units for the Carrier Air V. I recommend…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 10

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 11

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 12

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...