Help Accessing Taillight Housing Connectors for Installing Trailer Wiring 2018 Volkswagen Tiguan

Question

Question:

I understand the wiring requirements My problem, remove the tail lights to do the instalation. Thank you

asked by: Mike K

0

Expert Reply:

I attached a picture that shows how the very similar Curt trailer wiring harness part # C56403 installs which has a better set of instructions for accessing the taillight housings than the Tekonsha kit part # 118811.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 3

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Help Accessing Taillight Housing Connectors for Installing Trailer Wiring 2018 Volkswagen Tiguan

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching