Can L44643 Bearings and L44649 Bearings Be Exchanged

Question

Question:

Sorry gave you the wrong bearing # in last message.Can I use L44643 Bearings with Race number L44610 on the 8-91-05UC1 Hub? I have L 44643 can I use them with L44610 Race?

asked by: Judy

0

Expert Reply:

Yes, the Dexter Trailer Idler Hub Assembly part # 8-91-05UC1 will work with the bearing part # L44643 and the race part # L44610. They both have a 1.980" outer diameter which is why they are compatible with the above trailer hub. As long as your spindle has a 1" diameter where the bearing sits this option will work for you.

expert reply by: Conner L

0

Answer 1

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 2

The modern day size for a 20.5 x 8 x 10 sized tire is 205/65-10. Based on this information, I recommend The Kenda Loadstar Bias Trailer Tire Item #AM1HP56. It is a top-quality bias tire that is great for all terrains and provides a smooth ride. It…

view full answer...

Answer 3

Your 20.5x8.0-10 tire can be swapped to a 205/65-10 without issue at all. I suggest going with the Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel - 4 on 4 - Load Range D #AM3H410 as this will have a load rating D (1,320 pounds and 70…

view full answer...

Answer 4

The modern size equivalent of the 20.5x8-10 that you have currently would be the same size tire that is on the #AM3H340 that you referenced, 205/65-10. As long as the bolt pattern of your current hubs are 4 on 4 inch the wheels of this would bolt up…

view full answer...

Answer 5

From previous customers who have the same Floe Pro 100 trailer we have determined that the correct replacement hub would be for a 2k axle like with the part #AKIHUB-545-2-1K which is pre-greased.

view full answer...

Answer 6

The Kenda 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range B #AM30590 have a max speed of 65 mph. When trailer tires are not speed rated with a letter, the default is 65 mph max. I've attached an article to…

view full answer...

Answer 7

Luckily, FLOE International is still around. I was able to find that your 10 foot tilt single axle snowmobile trailer used an L44649 inner and outer wheel bearing. Your snowmobile trailer was equipped from the factory with idler hubs that had a 5 on…

view full answer...

Answer 8

I may have another option for you, but the Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72" Long - 2,200 lbs #T20BTR-EZ-7258 you were looking at uses inner and outer bearing #L44649 which is used for 2000lb hubs like the Dexter Trailer…

view full answer...

Answer 9

A 2000 lb axle uses a straight spindle, with both the inner and outer bearing being the same size. The hubs needed will depend on the number of lugs your current hubs have and which inner/outer wheel bearings are used. I'll give you a run-down on…

view full answer...

Answer 10

I have a solution for you. However, you are going to need a little more information to make sure you receive the correct hubs to replace you current oil bath hubs. You will need the bearing numbers of your current hub to match with the replacement…

view full answer...

Answer 11

Are you sure the diameter of the spindle is 1.25 inches where both bearings ride? That's not typical for a 2,000 lb axle but if instead the diameter is 1.06 inch then you could use the hub part #AKIHUB-545-2-2K which has the 5 on 4-1/2 bolt…

view full answer...

Answer 12

The difference between the L44649 and the L44649R is not the size of the race used as you have found. Typically the R indicates that the bearing was used in a higher capacity application. Dimensionally the bearings are the same and would take the…

view full answer...

Can L44643 Bearings and L44649 Bearings Be Exchanged

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching