Air to Electric Trailer Brake Controller

Question

Question:

AIR TO ELECTRIC BRAKE CONTROL

asked by: NEVILLE

1

Helpful Expert Reply:

We have the Hayes Air Actuated Trailer Brake Controller # HA100400C which is an air to electric brake controller like you need. This will connect to the air brakes of a trailer and allow you to operate electric trailer brakes.

expert reply by: Jameson C

1

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

While we do not carry that particular Lippert step we do have the similar MORryde #MR98RR or a better option in my opinion is the TorkLift GlowStep #TLA9104. I prefer this step as it folds up nicely and works better in tight areas like storage lots.…

view full answer...

Answer 7

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 8

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 9

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 10

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 11

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 12

The best brake controller for your 2024 Toyota Grand Highlander is from Redarc, and the correct part number for it and the needed wiring adapter is the following: - Redarc Tow-Pro Liberty Trailer Brake Controller #RED24FR - Wiring Adapter for Tow-Pro…

view full answer...

Air to Electric Trailer Brake Controller

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching