Chrome Lug Nut Recommendation for Use with Trailer Wheel # TA59RR and 1/2 inch Stud

Question

Question:

Do you offer chrome or stainless lug nuts for these wheels? 1/2 studs

asked by: Craig J

0

Expert Reply:

We have the chrome lug nut part # AM90049 which fits 1/2 inch studs like you have which would work well with the trailer wheel part # TA59RR.

expert reply by: Jameson C

0

Answer 1

For a 15 inch steel wheel such as #TA59RR and 1/2 inch studs you will want to torque the lug nuts to 90 to 120 foot pounds. For a basic torque wrench rated for 10 to 150 foot pounds we have #ALL944001 if you need one.

view full answer...

Answer 2

Since the Taskmaster Vesper Steel Modular Trailer Wheel #TA59RR has a weight capacity of 2,835 lbs it will do an excellent job at being able to hold up your 8K trailer with dual axles. This wheel does have 6 inch wide rims and a 5 on 4-1/2 inch bolt…

view full answer...

Answer 3

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 4

The break in process will be the same when replacing one brake and drum as if you were replacing both. Drive the trailer out into an open area, like an empty parking lot. Get up to around 40 MPH and apply the manual override on your brake controller.…

view full answer...

Answer 5

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 9

The Buyers Products 45 Ton Pintle Hook #337PH45 does not have the 4 inch square bolt pattern but rather uses a different pattern. Vertically the holes are 3 inches on center. Horizontally the top row is 5-1/4 inches on center and the bottom is 6-1/2…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Answer 12

The modern size equivalent of the 20.5x8-10 that you have currently would be the same size tire that is on the #AM3H340 that you referenced, 205/65-10. As long as the bolt pattern of your current hubs are 4 on 4 inch the wheels of this would bolt up…

view full answer...