How Does Brake Controller Install in 2017 GMC Canyon

Question

Question:

I have an explorer xp [previously installed in a nissan frontier] I need to install it in a 2017 GMC Canyon [pre-wired]. BTW, i bought the Carl tow receiver from you guys three weeks ago, and it went in quite nicely. I digress, Can this explor xp directly plug into the canyon or do I need to order a different harness from you guys?

asked by: JONATHAN Y

0

Expert Reply:

The brake controller you referenced is the Tekonsha Voyager Trailer Brake Controller # 39510 which can easily install in your 2017 GMC Canyon. Your vehicle does not have a plug-in style connector though to install the controller. Instead brake controller wire to the brake controller wiring that's under the dash. If you check out the install video I attached to this page you'll see how a similar brake controller installs in a GMC Canyon like yours.

expert reply by: Jameson C

0

Answer 1

When you add an aftermarket brake controller like the Tekonsha Prodigy P3 #90195 to your 2020 GMC Sierra 3500, you will need to have the computer flashed by a GMC dealer to disable the factory brake controller. If you do not do this the computer…

view full answer...

Answer 2

To install your Reese Pod brake controller in your 2018 Ford Explorer will require the install harness part #3035-P which is a confirmed fit. If you check out the 9:55 mark of the install video I attached to this page you'll see where to find…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 8

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

How Does Brake Controller Install in 2017 GMC Canyon

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching