TruXedo TruXport Tonneau Cover Replacement Tarp for 2014 Ram 6-1/2 Foot Bed

Question

Question:

I have a 2014 Dodge mega cab 6-4inch bed and need replacement cover?? Serial No: 018787409 Part No: 246901

asked by: Lyal M

0

Expert Reply:

Thanks for the information on your vehicle and tonneau. The part number helped me determine your tonneau as the TruXedo TruXport Soft, Roll-Up Tonneau Cover # TX246901. Based on that, the correct replacement cover/tarp is # TX2469-CVR.

expert reply by: Jason S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 3

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

We haven't had the opportunity to install the #EH97FR EcoHitch as of yet, but hen we installed the Curt #C13416 on a 2021 RAV4, we found that the inside top edge of the receiver tube sat about 12 inches above the ground, which would place the…

view full answer...

Answer 7

Yes we do, we have plenty to choose from. For your 2024 Toyota RAV4 I recommend checking out the Curt Trailer Hitch Receiver #C13416. This hitch has a 4,000 lb maximum capacity, a 600 maximum tongue weight capacity, and is made in the USA.…

view full answer...

Answer 8

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Answer 9

For your 2024 Toyota RAV4, the best trailer hitch receiver that will fit is the following: - etrailer Trailer Hitch Receiver #e23ZR The #e23ZR is the best because it has completely concealed crosstube so only the receiver is showing, allowing your…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4 Prime, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

TruXedo TruXport Tonneau Cover Replacement Tarp for 2014 Ram 6-1/2 Foot Bed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching