Could Replacement 2" Ball with Nut For Pintle Hitch # 337RB102000 be Used on Ball Mount

Question

Question:

Can you use this ball with a standard hitch mount?

asked by: Ryan

0

Expert Reply:

The non-threaded portion of the Replacement 2" Ball with Nut For Buyers Products Combination Pintle Hitch # 337RB102000 is taller than most hitch balls but it has a diameter compatible with a lot of ball mounts as it's shank diameter is 1-1/4 inch. With enough washers though I am sure it would work fine.

expert reply by: Jameson C

0

Answer 1

Thank you for all that info and we do have the perfect option for your needs, which is a weight distribution hitch for your range of tongue weight. I do highly recommend a hitch with sway control as a friction sway bar really isn't going to do as…

view full answer...

Answer 2

The max drop the #FA92-02-4315 that you referenced can do is 8 inches. Since you need right at 6 inches of drop to tow your trailer level this shank would work well for you. I attached a help article link on selecting the correct rise/drop ball mount…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 7

The correct hardware to use with the Buyers Products 3 Position Pintle Hook Mount part #337PM25812 will largely depend on what accessory will be attached to it. For example, the Buyers Products 10 Ton Combination Hitch with Mounting Kit part…

view full answer...

Answer 8

The Buyers Products 10 Ton Combination Hitch with Mounting Kit #33710057 has hole diameters of 5/8 inches. They are spaced 3-3/8 inches and 1-3/4 inches on center. I've attached a photo to assist as well as a video.

view full answer...

Answer 9

I attached a picture that has all of the mounting hole dimensions for the Buyers Products 10 Ton Combination Hitch with Mounting Kit #33710057 for you to check out. The distance between the two vertical mounting holes is 1-3/4 inches and the distance…

view full answer...

Answer 10

You do not lose any towing capacity when you use the Hidden Hitch Ball Mount #80232 despite it's longer length of 15 inches.

view full answer...

Answer 11

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 12

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Could Replacement 2" Ball with Nut For Pintle Hitch # 337RB102000 be Used on Ball Mount

Product Page this Question was Asked From

Continue Researching