How Tall is Trailer Hitch Ball 63840

Question

Question:

What is the height from the bottom of the mounting flange to the top of the ball?

asked by: Ernest C

0

Expert Reply:

I went and measured the height of ball # 63840 and from the bottom of the base to the top of the ball is 3.16 inches. That is a hair over 3-1/8 inches tall. I have found that this is a fairly common measurement having measured numerous hitch balls over the years.

expert reply by: Michael H

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The Electric Jack w/ Footplate and 7-Way Plug #EJ-3527-BBX uses a 7-way RV-style plug. I have included a diagram that shows the pin-out for RV style 7-way plugs. This will show you what each pin does. I have also listed the functions below and linked…

view full answer...

Answer 4

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

The round or trunnion bars refers to the end of the spring bars. Round bars are typically designed for lighter applications, are a bit harder to install and are usually priced lower than trunnion bars. Trunnion bars are typically designed to be used…

view full answer...

Answer 7

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 8

The vast majority of trailers on the market use a standard coupler (installed on top of the trailer frame) which is compatible with the B&W Continuum Weight Distribution System w/ Sway Control #BW28FR. Underslung couplers aren't as common but…

view full answer...

Answer 9

The Rhino Rack ROC25 part #RR46XR has a 165 lb dynamic weight capacity which means that's how much it can carry while travelling and incurring the standard bumps and movement that creates. While Rhino Rack doesn't give a static weight…

view full answer...

Answer 10

For your R-pod travel trailer, the biggest issue you will face is sway , so I recommend he Strait-Line Weight Distribution System w Sway Control - Round Bar - 10,000 lbs GTW, 600 lbs TW #RP66086 which is rated for total tongue weight between 200 and…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

The hitch ball angle adjustment on weight distribution systems is designed to provide more or less distribution of the tongue weight on your trailer hitch to the trailer and vehicle axles. If you adjust the ball angle farther away from the towing…

view full answer...

How Tall is Trailer Hitch Ball 63840

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching