Replacement Spring Latch for Ramp on Shadow Horse Trailer

Question

Question:

Hello, I was looking for a replacement part for my shadow horse trailer. The piece that holds the ramp up has completely come off. I’m looking for the spring load and the piece that attaches to the trailer. Do you know who I could contact to get this replacement? I have the measurements if needed. Thanks

asked by: Emily

0

Expert Reply:

Based on the photos I've seen online for Shadow Horse Trailers, it appears you are looking for the Bolt-On Stainless Steel Spring Latch # SL716SS. I've attached a video of this product as well as photo of the dimensions to further assist. I've also linked the page to all your spring latch options to assist if these measurements don't match.

expert reply by: Jason S

0

click to enlarge

Answer 1

I don't believe we have an exact match but we do have pins that you could potentially retro-fit to your trailer such as #F719-182Z104. The benefit of this design is that you can't lose the pins. I have included a link below to this…

view full answer...

Answer 2

To use a cam door style trailer latch on a trailer door that sticks out 1 inch past surface you'd want to use a spacer behind the latch mechanisms that attach on the door. I'd also go with a setup like the part #PLR258-002-SS which…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 5

The easiest way to go from a 7-way round connector to a 7-way flat would be to get a Trailer Connector Adapter part #HM47425. However, if you are looking for a more permanent solution you would need to remove your 7-way round connector and wire up…

view full answer...

Answer 6

The first thing that you need is the Trailer Connector Adapter #HM47425 which converts the 7-Way round connector on your 1999 International 9100 to a 7-Way blade style connector. This will plug into your 9100 and provide a pace to connect the…

view full answer...

Answer 7

We do offer the Trailer Connector Adapter, #HM47425, which converts a 7-pole round connector to a 7-pole flat connector. This adapter works for tow vehicles with combined taillight wiring, meaning that the turn signals and brake lights run on the…

view full answer...

Answer 8

To be frank the only difference you will really notice going to a larger ST225/75R15 tire with a load range of E over a ST205/75R15 tire with a load range of D is in your wallet. Slightly larger tires with a bit more capacity are going to cost you…

view full answer...

Answer 9

I attached a chart that has all of the recommended lug nut torque specs for trailer wheels. Based on your studs being 1/2 inch, your wheels being 15 inches in diameter, and your lug nuts being coned you would want to torque your lug nuts to 90-120 ft…

view full answer...

Answer 10

Bearing Buddies #BB1980T-SS are going to be the best match for your 1.988 hub bore. Nothing else we have comes close. These are threaded Bearing Buddies, the only option in this size that is threaded. For 2 pair you would just change the quantity to…

view full answer...

Answer 11

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Replacement Spring Latch for Ramp on Shadow Horse Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching