What Size Channel Does Channel Tongue Coupler part # CT-3001-Z Fit

Question

Question:

Does a 2inch Channel coupler fit over 2inch sq. tubing??

asked by: Mark

0

Expert Reply:

Yes, a coupler like the Channel Tongue Coupler part # CT-3001-Z that you referenced which is designed for a 2 inch channel is designed to fit a 2 inch square tube.

expert reply by: Jameson C

0

Answer 1

No, the hole spacing on coupler #CT-3001-Z is actually 3-1/16 inches as measured by our video demonstrator in the video I have linked. The holes for coupler #CT-2001-Z are spaced 2-1/4 inches apart on center.

view full answer...

Answer 2

For a 4-pole round trailer connector and socket, I would recommend looking at the Pollack Heavy-Duty 4-Pole Round Trailer Connector, #PK11409, and the Pollack Heavy-Duty 4-Pole Round Trailer Socket, #PK11410. The connector and socket have a…

view full answer...

Answer 3

We have trailer LED tail lights that similar to the Wesbar lights with a driver side license plate bracket that is a bit narrower than the top of the light. The light is from Optronics and measures 7-1/2 inches wide on top and the license plate…

view full answer...

Answer 4

The housing is ABS, a thermoplastic for the Optronics LED Trailer Clearance and Side Marker Light - Chrome Plated - 6 Diodes - Amber Lens #MCL81AB. If that's what you were looking for, there is also an option with a red lens, the LED Clearance…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

What Size Channel Does Channel Tongue Coupler part # CT-3001-Z Fit

Product Page this Question was Asked From

Continue Researching