Threads Per Inch of Lug Nut 6-109

Question

Question:

What is the thread pitch for this nut?

asked by: John Z

0

Expert Reply:

Trailer Wheel Lug Nut - 5/8" # 6-109 is 18 threads per inch. It has a 1-1/16" outer diameter, is 90 degree coned and fits 5/8" wheel bolts. TPI is used for standard measurements while pitch is for metric, which is why there isn't a pitch, just a TPI.

expert reply by: Kyle S

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 6

Hey Luis, for your 2018 Ford F-350 that doesn't have the OEM pucks you would want the B and W Turnoverball hitch part #BWGNRK1116 that is a confirmed fit for your truck. I really like the B and W gooseneck hitches as they are known to be the…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Yes, it will! The 5" Offset Gen-Y Hitch Gooseneck Trailer Hitch item #GY43XR is specially designed to work with the Ford factory puck system. It will push the connection point for the gooseball and your cattle trailer back 5" towards your…

view full answer...

Answer 10

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 11

It is certainly possible for the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY58GR to work on your 2020 Ford F-250 Super Duty short bed, but there are likely going to be clearance issues as these are meant for long bed trucks. That…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Threads Per Inch of Lug Nut 6-109

Product Page this Question was Asked From

Continue Researching