7-Way Recommendation for 1990 StarCraft Star Flyer

Question

Question:

We are looking for a 7 prong pluggin for a 1990 StarCraft Star Flyer 1990 Pop Up Camper. Thank you.

asked by: Marie M

0

Expert Reply:

For a new 7-way plug the part # H20046 is an 8 foot long plug that would work well. This is a 7-way RV style plug. I attached an install video for this plug for you to check out.

expert reply by: Jameson C

0

Answer 1

If your 2023 Toyota Tacoma doesn't have any trailer wiring you would first need to start with a 4-way like the part #C56349 which is a confirmed fit and then install a 4-way to 5-way kit like the part #C57187 which would run to your reverse light…

view full answer...

Answer 2

The Buyers Products Hour Meter part #337B40B45 can be wired to any 10-80 VDC accessory that you need to monitor the run time on. It is primarily used for equipment maintenance and repair schedules. It will simply install inline on a power wire that…

view full answer...

Answer 3

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 4

On the 7-way wiring plug and lead part #H20046 there isn't a purple wire. Normally a purple wire for a 7-way is for a reverse light circuit. Which would correspond to the yellow wire of this adapter.

view full answer...

Answer 5

You definitely could install the 7-Way Molded Trailer Wire Connector #H20046 in place of the 5-way that is installed on your trailer currently. The colors wouldn't match up exactly. White would go to white, you would run both brown wires to the…

view full answer...

Answer 6

There's not a universal way that trailers are wired. I have attached a diagram showing the three typical ways and this should also help you to connect to the 7-way harness you purchased once you identify your wires. Yours is obviously different,…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

7-Way Recommendation for 1990 StarCraft Star Flyer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching