How to Change Height of Fulton Jack Mounting Bracket

Question

Question:

how do i adjust the height of the mounting bracket? i loosened the bolt behind it

asked by: Arnold

0

Expert Reply:

To adjust the height of the mounting bracket on the Fulton F2, part # F1413040134, you need to loosen the bolt behind the bracket (which it sounds like you have) as well as the bolt in the middle of the bracket. Take a look at video that I have attached for you.

Make sure to tighten both bolts back to spec per the instructions after adjusting the height.

expert reply by: Charles S

0

Answer 1

It sounds like you are actually needing the Replacement Hardware Kit for Fulton Swivel Jacks #F0933325S00.This fits a mounting plate like the #P9012-00 that it sounds like you have welded to your trailer. It includes the metal bushing/washer that…

view full answer...

Answer 2

If the swivel jack you have is a Fulton the sleeve washer that comes with the part #F0933325S00 that you referenced would replace what you have and would prevent your jack from leaning like you mentioned.

view full answer...

Answer 3

I believe what you're needing is the washer looking piece in the Replacement Hardware Kit for Fulton Swivel Jack #F0933325S00.

view full answer...

Answer 4

The Replacement Hardware Kit for Fulton Swivel Jack #F0933325S00 is a direct replacement from Fulton that is designed to fit only Fulton-model swivel jacks. However, there is a possibility that you will be able to use the hardware for your specific…

view full answer...

Answer 5

I went out to the warehouse to measure Dutton-Lainson trailer coupler #DL13897 for you. The base where the mounting holes are is 2-1/4 inches. From the bottom to the top of the closed latch is 4-1/8 inches. And with the latch open it is 6-1/8…

view full answer...

Answer 6

The spare tire can be mounted near the wheel and axle to the frame, but you will want more than 5 inches of ground clearance. I recommend the Extra Offset Trailer Spare Tire Carrier by Dutton-Lainson #DL22145 based on your photo. Every extra inch…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

How to Change Height of Fulton Jack Mounting Bracket

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching