Solution for Truck Bed Camper Jacks with Bad Gears

Question

Question:

I have a 1973 Ford slide in camper that uses jack stands see attached picture. The gears need to be replaced on two jacks see attached picture. Appreciate any help!

asked by: Frank R

0

Expert Reply:

We have excellent options for replacing your truck bed camper jacks but we do not have a way to get the gears you'd need for the jacks that you currently have. Based on that you'd want the Brophy Cable Camper Jacks # CJ31 which has a 1,000 lb capacity.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 have a minimum reach of 16-1/2". This means your tie-downs need to be at least 16-1/2" away from the attachment points on your camper. The best way to determine fitment would…

view full answer...

Answer 2

The Brophy Cable Camper Jacks #CJ31 has tripod feet with the longer two legs sitting at almost a 90 degree angle in proportion to the smaller leg. Since they don't sit at a perfect 90 degree angle they will be slightly under the L-brackets that…

view full answer...

Answer 3

The handle on Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Travel - 5,000 lbs Item #TJDA-5000S is held to a gear with a roll pin and into the jack with e-clips. It would require modification and fabrication to link two of…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 6

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 7

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...

Answer 8

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 9

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Solution for Truck Bed Camper Jacks with Bad Gears

Product Page this Question was Asked From

Continue Researching