Insect Screen Sizing to Cover Water Heater Vent on RV

Question

Question:

I would like to know if this part would fit the exhaust vent on my Suburban SW6DEL water heater. This part comes up when I search my model, but my vent measures 5inch x 5, when the one you list here says it is 6.25inch x 6.25.

asked by: Randy B

0

Expert Reply:

The Camco RV screen, part # CAM42151, does measure 6-3/4 by 6-3/4 inches; however, that doesn't mean it won't fit your vent. As you can see in the attached picture the screen can be larger than the vent.

expert reply by: Charles S

0

click to enlarge

Answer 1

I have a couple screens that are close to the dimensions you mentioned. They are the Valterra Bug Screen #A10-1322VP (suburban Models) which is going to be 4.5" x 4.5" and the Valterra Bug Screen #A10-1320VP (Atwood & Suburban) which is…

view full answer...

Answer 2

I spoke with Yakima, and they said for your Landing Pad 27 for Yakima SkyLine And Control Towers #Y46VR, you can use the: -Replacement Cover for Yakima LandingPads #Y8890029 as a replacement cover.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Insect Screen Sizing to Cover Water Heater Vent on RV

Product Page this Question was Asked From

Continue Researching