Locating Brake Light Switch on 2005 International 8600 Truck

Question

Question:

Need to know where is the brake light switch on a 8600 05 International

asked by: Elton

0

Expert Reply:

If your 2005 International 8600 has hydraulic brakes, then the brake light switch should be located somewhere right above the brake pedal. I was unable to locate what color this wire might be, so you will simply need to test the factory wires with a circuit tester like # PTW2993. You are looking for the wire that only receives power with the brake pedal depressed, and no power with any other function.

Once found, this is the wire that will connect to the red wire on the Tekonsha Prodigy P3 Brake Controller # 90195 that you were looking at.

expert reply by: Chris R

0

Answer 1

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 2

Typically 1-1/2 to 1-3/4 inch diameter axles have 1,000-1,200 lb capacities. Since your axles are smaller than that I can only assume slightly less than 1,000 lbs. On some trailers there will be a plate or sticker that will list the trailer…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 10

Hello John. The #C96JR tail light kit for the 2023 Jeep Gladiator will indeed work with a Brake Buddy brake System Such as part #HM39524. So, if you plan to use a portable brake system, that is definitely what I recommend, and you do not need to get…

view full answer...

Answer 11

There are a number of factors involved when converting a semi 7-way to an RV 7-way. Semis generally use a 7-pin round pin socket, similar to #PK11720. And RV style 7-way uses blades, like #PK12706. We do not offer any pre-made adapters to make this…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Locating Brake Light Switch on 2005 International 8600 Truck

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching