4-Pole Trailer Wiring Harness for 2006 Ford Escape Without Factory Tow Package

Question

Question:

2006 ford escape The fuze box #1 for tow lights is just an empty hole , no tabs to hold the fuze. I assume the factory connection in the rear of the truck goes somewhere? Only thing i can think of to do is connect to the tail light wires. Any advise would be greatly appreciated.

asked by: Gary D

0

Expert Reply:

It sounds like you need 4-pole trailer wiring for your 2006 Ford Escape that does not have a factory tow package.

We do offer a harness # 118426 that will install at your two tail light assemblies and through a single wire connecting to your battery positive terminal. An installation video and article and linked to help you. I suggest using dielectric grease # 11755 on the connectors to protect them from corrosion.

This harness will provide all basic trailer lighting signals and will also protect your Escape's factory wiring from any risk of damage from a short-circuit on the trailer.

expert reply by: Adam R

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 4

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 5

The Torflex Lift Kit #K71-724-02 is meant specifically for the #11 Torflex axles and attaches directly to the side mounted brackets on your trailer's frame without any additional hardware. This kit works with Torflex Axles with a 4,100-6000 lb…

view full answer...

Answer 6

Basically you would need to replace the rear hanger with a double eye style hanger, use a shackle strap and then get the appropriate leaf spring. The lightest capacity spring we have is the part #e84SR which you referenced. For the price the best…

view full answer...

Answer 7

I can help explain the difference between the listing for towing weight and weight distribution towing capacity for you. Let's use the Draw-Tite Class V Trailer Hitch #DT45502, which is a confirmed fit for you 1992 Ford, that you were looking at.…

view full answer...

Answer 8

To use the Inno Dual Angle Ski and Snowboard Carrier INUK729 with your 2016 Honda Fit you are going to need to use the: -Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK876 as well.

view full answer...

Answer 9

The correct bearing kit for your 2000 Trailstar 8 camper will depend on your other bearing and grease seal. If the #L44649 is your inner and outer bearing then you need the Bearing Kit, L44649 Inner/Outer Bearings, 10-60 Seal #BK1-150. I recommend…

view full answer...

Answer 10

The best way to tow your Kawasaki Ninja with your Ford Escape is going to be with the etrailer Trailer Hitch item #e56AR. This hitch is custom fit and bolts to your Escape with included hardware. It is confirmed to fit the Hybrid model Escapes. I…

view full answer...