Bolt Hole Dimensions of Stromberg Carlson Motor Home Hitch Receiver

Question

Question:

What are the bolt hole dimensions?

asked by: Garry H

0

Expert Reply:

The Stromberg Carlson 2" Motor Home Hitch Receiver for 4-1/2" x 4" Bumpers - 200 lbs # BA-100 has a 6 inch square base and bolt holes that are 5 inches on center. I've attached a photo and video to assist. The bolt holes are about 1/2 inch diameter.

expert reply by: Jason S

0

click to enlarge

Answer 1

We will have a trailer hitch receiver that is able to be mounted to your 2021 Winnebago Micro Minnie 225RL, but you will need to determine the correct one. From the photos I saw it looks like this trailer does have a bumper and spare tire, so you…

view full answer...

Answer 2

What I recommend for a bumper mount hitch is to go with #BA-100 which fits 4 x 4-1/2 inch bumpers. However, use a bumper mount hitch only if it is a square continuous welded steel bumper. If the bumper is not square, not continuously welded, and/or…

view full answer...

Answer 3

The Stromberg Carlson 2" Motor Home Hitch Receiver for 4-1/2" x 4" Bumpers - 200 lbs #BA-100 does not have manufacturer instructions for installation available online. I've attached a video to assist but the…

view full answer...

Answer 4

Since it looks like you have C-channel on your 2021 Winnebago Micro Minnie FBS Comfort Explorer you'd have to find a welder to box the frame so that you can then install the Mount-n-Lock SafetyStruts #MO22FR that you referenced but it can…

view full answer...

Answer 5

The Draw-Tite Max-Frame Trailer Hitch Receiver #75282 will have the following bolt hole dimensions for your 2015 Nissan Frontier. The Bolt holes from drivers side to passenger side frame rails are 43-5/8" on center. The holes running from…

view full answer...

Answer 6

Hey William, the E6 error on a Furrion wall thermostat indicates an Open circuit Humidity Sensor issue. Most likely the sensor is bad and needs to be replaced as this is a pretty rare error code.

view full answer...

Answer 7

We do have awning power switches with four wires in both black and white, the Replacement Switch Kit for Solera Power RV Awnings part #LC285499 for white or part #LC285500 for black. Please note, if your wire colors don't match you will need…

view full answer...

Answer 8

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 9

The Brophy Rigid Mount Spare Tire Carrier #BR56VR will allow you to carry a spare tire with Wheel #TA56FR on your 4" RV Bumper. I have included an image below of a similar setup so you can see how it fits.

view full answer...

Answer 10

I went through all of our shocks for trailer surge brakes and did not find an exact match. A similar one is the Demco #DS12426 replacement shock. This shock measures 6” eye to eye compressed, and 8-1/8” extended. In my research I found out MaeCo has…

view full answer...

Answer 11

I will start by saying the ARK Extreme Off-Road Ratcheting Trailer Jack w/ Wheel #ORJW1SU will fit frames that are 2" to 6" tall. The bolt hole measurements vary and I included a diagram with everything listed, but the overall dimensions of…

view full answer...

Answer 12

Bike carriers that are designed to work on the rear of an RV are made so that they can take the additional stress at the back of the RV. Yakima does not recommend using the HoldUp Rack on RVs because a bike rack mounted on the rear of a motor home…

view full answer...