How to Lock Bikes to Older Model Thule Vertex Bike Rack

Question

Question:

Hi, I have an older version of the Vertex without the integrated lock. Any suggestions for locking the bike to the rack?

asked by: Dan

0

Expert Reply:

To lock your bikes to your older model Thule Vertex Bike Rack, I just recommend using a cable lock like the # e98891. You can weave the cable around your bikes and then through the safety chain loops on your trailer hitch, which will also secure the rack to your vehicle.

I have attached a short video demonstration on this cable lock that you can also check out.

expert reply by: Chris R

0

Answer 1

Yes, the Anti-Rattle Device and Lock for 2 inch Trailer Hitches, item #SR25219, will work with the 2 inch Cargo Carrier, item #63153.

view full answer...

Answer 2

It sounds like the lock core isn't seated properly in your Thule Snug Tite Hitch Lock and Anti-Rattle Device #THSTL2. I've attached a video to help you with this installation as the core should be slightly recessed when installed correctly.…

view full answer...

Answer 3

The SoftRide Anti-Rattle lock you mentioned, part #SR25219 is an excellent product, but it is not compatible with the threaded shank of Thule bike racks. Thule makes a Snug Tite hitch lock and anti-rattle device, part #THSTL2 that is compatible with…

view full answer...

Answer 4

The Thule Snug Tite Hitch Lock and Anti-Rattle Device part #THSTL2 will be the only hitch lock we have that is confirmed to work with a Thule bike rack. The majority of hitch locks for bike racks are specific to that rack and cannot be exchanged for…

view full answer...

Answer 5

We sell several hitch locks for bike racks. Many times, bike rack manufacturers use threaded hitch pins, so you use a brand specific hitch lock. In one of your previous questions, it looks like you were interested in the Thule Parkway 4 Bike Rack.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The Curt #C13410 and Draw-tite #76227 are very similar in design and both have the same weight ratings of 600lbs tongue weight and 4,000lbs of trailer weight. I do like that Draw-Tite does add the additional plate of steel in between the hangers that…

view full answer...

Answer 11

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

How to Lock Bikes to Older Model Thule Vertex Bike Rack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching