Replacement Keel Roller Only or Keel Roller with Mounting Bracket
Question:
I need to replace the keel roller on my easy loader trailer. Roller is 1/2 way up, a bit toward bow. I do have self adjusting rollers mounted seperately on each side of the keel roller assembly. boat is 16foot Boston Whaler. Just roller or should I get with bracket ?
asked by: Allan
Expert Reply:
If your bracket is in good shape, not bent up or corroded then it is perfectly fine to replace just the roller with one of the same size. Roller # YR800Y has a 3-1/2 inch diameter at the widest point, it is 7-3/4 inches long overall, and fits a 5/8 inch diameter shaft.
If you do need or want to also replace the bracket I recommend # CE10453G which is already assembled and ready for install.
It is easiest and best to replace rollers while the boat is off of the trailer. That way you aren't putting additional stress on any other roller or support part of the trailer for an extended period of time.
Products Referenced in This Question
CE Smith Deep V Keel Roller Assembly for Boat Trailers - Galvanized Steel and Yellow TPR - 8"
- Boat Trailer Parts
- Rollers
- Keel Roller
- Thermoplastic - Non-Marking
- 8 Inch Long
- CE Smith
more information >
Product Page this Question was Asked From
Yates Keel Roller for Boat Trailers - TPR - 8" Long - 5/8" Shaft
- Boat Trailer Parts
- Rollers
- Keel Roller
- 3-3/16 Inch Diameter
- Thermoplastic - Non-Marking
- 7-3/4 Inch Long
- Fits 5/8 Inch Shaft
- Yates Rubber
more information >
Continue Researching
- Video: Review of Yates Rubber Boat Trailer Parts - Roller and Bunk Parts - YR800Y
- Video: Review of CE Smith Boat Trailer Parts - Roller and Bunk Parts - CE29517
- Search Results: 8 v keel roller
- Search Results: boat trailer bunk brackets
- Shop: Yates Keel Roller for Boat Trailers - TPR - 8" Long - 5/8" Shaft
- Shop: CE Smith Deep V Keel Roller Assembly for Boat Trailers - Galvanized Steel and Yellow TPR - 8"
- Article: How to Choose the Best Winch for You, your Boat, and your Trailer
- Q&A: How Does the CE Pyramid Washer # CE10806 Fit Against a U-Bolt Nut
- Q&A: Distance Between Mounting Holes of Swivel Bracket for Boat Trailers HP23FR
- Q&A: Recommended Swivel Bracket for Bunk Board with 2 Inch Bolt Spacing
- Shop: CE Smith Bolt for Bolster and Swivel Bracket Assemblies - 1/2" Diameter - Zinc - Qty 1
- Shop: CE Smith Swivel Bracket for Boat Trailers - Galvanized Steel - 2" Hole Centers - Qty 1
- Shop: CE Smith Pyramid Washer for 7/16" Shaft - Zinc-Plated Steel - Qty 1
- Shop: CE Smith Flat Washer - 1/2" Inner Diameter - Zinc
- Shop: CE Smith Wobble Roller Retainer Ring - Zinc-Plated Steel - Qty 1
- Q&A: Bunk Boards and Brackets That Allow for Angle Adjustment
- Q&A: Is the Mounting Bracket of the CE Smith Bolster and Swivel Mounting Brackets Bent at 90 Degrees
- Q&A: Does Boat Have to Be Off Trailer to Install New Boat Bunk Boards
- Q&A: How To Determine Correct Bunk Boards and Mounting Hardware For 17' V Bottom Boat
- Video: Yates Rubber Boat Trailer Parts - Roller and Bunk Parts - YR510Y-4 Review
- Search Results: 58 roller shaft
- Video: Choosing the Right Trailer Wiring
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: 68149
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Fifth Wheel Hitch