Brake Controller Install Port Location for 2015 Ford Chassis E-350 Cutaway

Question

Question:

We have a 2015 Thor Axis 24.1 and need to hook up a brake controller. Cant find the wiring for it on this chassis. Do you know where it is located?

asked by: Joy V

0

Expert Reply:

I attached a picture that shows where you'll find the brake controller install harness plug for your 2015 Thor Axis 24.1 built on a E-350 cutaway chassis. You'll want to use the # 3034-P which is a confirmed fit for the vehicle.

The port should be located behind the access panel in the center of the dash. You can use a trim panel puller to carefully pry the panel out, then undo the locking tabs to remove the panel. The connector will be behind this panel. I've attached an image showing the port's location.

For a brake controller, I recommend the Tekonsha P3 # 90195. This is a proportional brake controller that applies pressure to your trailer brakes in proportion to your vehicle's braking action. It has an easy-to-read LCD display and 3 boost levels for braking power adjustment.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The correct brake controller harness for your 2023 Ford E-350 to install a Tekonsha Prodigy P3 part #90195 is the part #22292. The connector on your E-350 is in a really unusual location behind the vents above the stereo. To see how to access it…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Brake Controller Install Port Location for 2015 Ford Chassis E-350 Cutaway

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching