Recommended While LED Lights with Clear Lens for Courtesy Lamps

Question

Question:

Apparently I didnt read the entire description of these lamps. I wanted clear lens white lights that fit into those brackets. My truck has four Amber and two White on each side. The Amber are marker lights and the White are courtesy lamps which come on when a door is open to light up the running board. My truck was equipped with incandescent lamps and I want to convert to LED. Is there a clear lens three diode white light that will fit into these brackets? Thanks

asked by: Kevin P

0

Expert Reply:

We do not carry and clear lens with white LED in that # AL91CAB size. You may want to consider instead using the Optronics Sealed LED Utility Light - 2 Diodes - Clear # UCL13CPG or the Thinline Sealed LED Utility Light - Clear - 6 Diode # UCL65CB as an alternative. Another option is the Sealed Waterproof LED Utility Light # UCL19CB for a polished housing.

expert reply by: Jason S

0

Answer 1

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 2

A 16 inch tire will not fit on a 16.5 inch wheel. You would either need to get new 16 inch wheels with the proper bolt pattern to match what the hubs require or to get your existing wheels you would need to go with 16.5 inch tires. You mentioned you…

view full answer...

Answer 3

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 4

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 5

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 8

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 9

I agree, the bag for the NOCO Boost X Jump Starter #NOC88VR is a nice way to keep everything together but it definitely lacks in the protective department. To keep your Boost X Jump Starter safer you'll want to pick up the EVA Protection Case…

view full answer...

Answer 10

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Recommended While LED Lights with Clear Lens for Courtesy Lamps

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching