Dimensions of Curt Double Lock, Flip and Store Gooseneck Hitch

Question

Question:

Curt 60607 hitch plate.....can you tell me how wide and long mount plate is ...thank u

asked by: Lonnie H

0

Expert Reply:

The Curt Double Lock, Flip and Store Gooseneck Hitch # C60607 measures 7.75" wide and 24.375" long according to the representative of Curt that I spoke with.

To install it in your 2004 Ford Super Duty you would need the installation kit and the hitch and kit together is part # C60720, which will fit in either a 6-3/4' or 8' bed of your '04 F-250 or F-350.

I've added a link to a video review of this part for you to check out.

expert reply by: Kyle S

0

Answer 1

To install a gooseneck hitch in the bed of your 2003 Ford F-250 all you would need is the Curt Hitch part #C60720 that you referenced. This comes with everything needed to complete the install.

view full answer...

Answer 2

For the short bed 2005 Ford F-250 the center of the hitch ball hole when you install the Curt hitch #C60720 will need to be drilled 35 inches from the front edge of the truck bed.

view full answer...

Answer 3

On a 2000 Ford F-250 or F-350 you will measure from the rear edge of the truck bed (not the tailgate) forward 48-1/4 inches to drill the hole for the gooseneck ball when installing Curt hitch #C60720. I have included links to the 2 sets of…

view full answer...

Answer 4

You could go to the very rear of the truck bed where the bed liner ends and measure from left to right there to get the left and right center and then take that measurement forward. The bed liners are also really well made now that if you used the…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 12

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...