Curt Gooseneck Hitch Recommendation for a 2003 Ford F-250 Long Bed

Question

Question:

this kit includes everything to be able to install in the truck 2003 ford f-250 super duty extended cab So then I do not have to buy any more kits to pull a gooseneck trailer

asked by: Mike

0

Expert Reply:

To install a gooseneck hitch in the bed of your 2003 Ford F-250 all you would need is the Curt Hitch part # C60720 that you referenced.

This comes with everything needed to complete the install.

expert reply by: Jameson C

0

Answer 1

You could go to the very rear of the truck bed where the bed liner ends and measure from left to right there to get the left and right center and then take that measurement forward. The bed liners are also really well made now that if you used the…

view full answer...

Answer 2

For the short bed 2005 Ford F-250 the center of the hitch ball hole when you install the Curt hitch #C60720 will need to be drilled 35 inches from the front edge of the truck bed.

view full answer...

Answer 3

The Curt Double Lock, Flip and Store Gooseneck Hitch #C60607 measures 7.75" wide and 24.375" long according to the representative of Curt that I spoke with. To install it in your 2004 Ford Super Duty you would need the installation kit and…

view full answer...

Answer 4

When you install a fifth wheel rail kit like the custom kit part #RP50082-58 in the bed of your 2002 Ford Super Duty long bed the king pin center will be approximately 52-5/16 inches from the rear edge of the truck bed. The rear edge of the rear rail…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Curt Gooseneck Hitch Recommendation for a 2003 Ford F-250 Long Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching