Replacement Spring Pin for a Yakima HoldUp Bike Rack

Question

Question:

Will this spring pin also fit the Yakima Holdup 2 bike rack?

asked by: Keith C

0

Expert Reply:

The replacement spring pin for Yakima HoldUp bike carriers made after Fall of 2015 would be # 8880582. It is the only spring pin listed for the HoldUp bike racks.

expert reply by: Michael H

0

Answer 1

The Replacement Latching Spring for Bike Racks item #8880582 you referenced fits the Yakima HoldUp models #Y02443, #Y02443-2, or #Y02445. The Replacement Spring Pin for Yakima Hitch Mounted Bike Racks item #8890314 you were looking at only fits the…

view full answer...

Answer 2

If you take a close look at the Replacement Latching Spring Pin part #8880582 you will see that the cylindrical body has two notches on either side. If you take an opened ended wrench and place it over the body while aligning it with these notches…

view full answer...

Answer 3

I went out to the warehouse to measure the Replacement Latching Spring Pin #8880582 and while I was able to confirm that it is essentially what you measured (between 23 and 24 mm), I wasn't able to get an exact measurement as the bag it is in is…

view full answer...

Answer 4

If your HoldUp was manufactured between 2008-2009, you'll need #Y39FR. If you have a HoldUp EVO, use part #Y57FR. If your HoldUp was built after 2009 let me know, and we can search further. If you're referring to the latching spring pin, we…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...