Can Fulton Drop-Leg Stabilizer Jack with Mounting Channel be Welded to an Aluminum Frame
Question:
Are there concerns for welding this on an aluminum trailer? Steel sleeve against aluminum frame, wont that cause corrosion? Looking for something to put on tail of enclosed trailer to allow loading of Harleys when not attached to truck.
asked by: Eric R
Helpful Expert Reply:
The biggest issue you will run into is the actual welding process. There are different heat requirements for aluminum components and steel components. Not that it can't be done but the welder would need to have experience welding steel to aluminum.
There is also the issue of galvanic corrosion that you mentioned. Your best option is to use a couple of scissor jacks, # UF48-979002, and bolt them to the bottom of the trailer frame. This will allow you to paint, prime, or otherwise treat the area where the jacks will be to minimize the chance of galvanic corrosion. You could then use adapter # UF48-979005 with an electric drill to make raising and lowering the jacks easier and faster.
Products Referenced in This Question
Ultra-Fab Ultra Scissor Jacks - 24" Lift - 13,000 lbs - Qty 2
- Camper Jacks
- Fifth Wheel Camper
- Pop Up Camper
- RV Motorhome
- Teardrop Camper
- Travel Trailer
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Scissor Jack
- 24 Inch Lift
- Bolt-On
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Tools
- Ultra-Fab Products
more information >
Continue Researching
- Shop: etrailer E-Track Backing Plates w/ Hardware - Galvanized Steel - 6" Long x 6" Wide - Qty 4
- Shop: Ark Drop Down Corner RV Stabilizer Jacks - 24" Long Corner Steadies - Silver - Qty 2
- Shop: Erickson E-Chock Wheel Chocks for E Track - Powder Coated Steel - Qty 2
- Search Results: e track anchor
- Search Results: e track backing plate
- Q&A: Mounting Orientation of TJ01RT-HD Stabilizer Jack
- Shop: Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs - Qty 1
- Shop: Fulton Square Mounting Channel for Drop-Leg Stabilizer Jacks - Weld-On - 13" Long
- Shop: Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
- Shop: Stallion Stabilizer Jacks - 7" Drop Leg Travel - 22-1/4" - Qty 2
- Search Results: e~track wheel chocks
- Q&A: PSI Rating for ST205/75R14 Load Range C Trailer Tires
- Video: etrailer E-Track Backing Plate with Hardware Review and Installation
- Video: Erickson E-Track E-Chock Wheel Chocks Review
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Video: Lippert Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System Review
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Shop: Trailer Hitch
- Search Results: 25580
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Video: Trailer Valet 5X Swivel Jack and Trailer Mover Review
- Shop: Trailer Wiring
- Q&A: Seal With Dimensions to Replace 171255UC
- Shop: Fifth Wheel Hitch
- Search Results: 68149
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: etrailer Horizontal E-Track Review
- Shop: Brake Controller