Troubleshooting Installation Of Air Lift LoadLifter 5000 Air Helper Springs - Item # AL57200

Question

Question:

My truck has a helper spring, am I going to have to remove helper spring for the air bags to work?

asked by: James M

0

Expert Reply:

Based on your information, it looks like the helper spring is preventing you from fully installing the Air Lift LoadLifter 5000, Item # AL57200. To complete your installation, you will need to remove your helper spring.

I have also attached an installation video for a 2014 Ford F-150 that might help.

expert reply by: Brint H

0

click to enlarge

Answer 1

The door latches for your Furrion RV Refrigerator - 4 Door - Stainless Steel - 14 Cu Ft #FCR14ACBQASS are part #7 in the diagram below and can be activated by simply pushing the doors in until you hear a click noise.

view full answer...

Answer 2

We used a 14mm socket to remove the jounce bumper on a 2014 and 2015 Ford F-150. The jounce bumper is about 4 inches long, so you will want to use an extension. I would use a 4 inch extension if you are using a standard socket and a 2 inch extension…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Troubleshooting Installation Of Air Lift LoadLifter 5000 Air Helper Springs - Item # AL57200

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching